Serial interface boards (RS 422/485/232)

A serial data transfer is normally used when data has to be sent over a distance of more than 10 meters. In contrast to the parallel interface, the data is sent bit by bit (serial). Additionaly, start, stop and parity bits are inserted into the data stream. While the parallel interface uses eight wires plus control wires, the serial only needs two. To guarantee a safe and error-free transfer in all circumstances, standards were defined.


PCI

		interface(s)			software
	bus	number	type	speed	IRQ	compatibility	Win2000 / Win98

PCISER2	PCI	2	RS-232	max 811.6 KBaud	PCI		yes
	32-bit PCI serial card with two ports Compatible only with plug and play motherboards Supports IRQ Sharing - All ports use only a single IRQ ! Jumperfree Drivers for Windows 95 / 98 / ME / NT / 2000 Automatic installation as the last two serial interfaces More info...

PCISER4	PCI	4	RS-232	max 811,6 KBaud	PCI		yes
	32-bit PCI serial card with four RS232 ports Compatible only with plug and play motherboards Supports IRQ Sharing - All ports use only a single IRQ ! Jumperfree Drivers for Windows 95 / 98 / ME / NT / 2000 Automatic installation as the last four serial interfaces More info...

PCISER8	PCI	8	RS-232	max 921,6 KBaud	PCI		yes
	32-bit PCI serial card with eight ports Compatible only with plug and play motherboards Supports IRQ Sharing - All ports use only a single IRQ ! Jumperfree Drivers for Windows 95 / 98 / ME / NT / 2000 Automatic installation as the last eight serial interfaces More info...

Glossary:

RS-232
This interface standard is designed for two communication devices which each use a data source and a data sink. For data transfer, three wires are needed, a send wire (TX), a receive wire (RX) and a common ground.
The signals of RS-232 are bipolar. A logical ‘0’ is represented by a voltage of +12 Volt, a logical ‘1’ by -12 V. The ratio of signals and disturbance is therefore significantly bigger than on a parallel interface. This makes it possible to transfer data over relatively long distances without bigger disturbance.
Cable lengths of more than 20 meters are not recommended.
double-current, also named TTY
This transfer type uses a wire with impressed current (20 mA). Therefore, the voltage loss does not influence the transfer that much so that cable lengths of up to 100 meters can be used.
The data signal is transfered in push-pull operations (like the RS-422), which significantly reduces the disturbance and overcoupling. Therefore, smaller signal amplitudes can be used (e.g. +/- 5V).
The maximal data transfer rate is 115 kBd.

RS-422
This standard is used for the communication between a sender an a receiver. Four wires are needed, two send wires and two receive wires which are used alternately. On these wires a logical ‘1’ is represented by 5V on the upper wire (TX+ or RX+) and 0V on the lower wire (TX- or RX-),a logical ‘0' the other way round.

RS-485
The wires on this interface are used in push-pull operations like on the RS-422; however, only two wires are needed which are used in half-duplex mode.
Besides, the RS-485 supports the use of more than one sender or receiver by the use of a protocol. RS-485 supports cable lengths of up to 1.2 km and data transfer rates of up to 1 MBit/s (depending on the serial controller)
Data source, data sink
A data source or data sink is a data end unit, e.g. a PC, which sends and receives data. The data is is always sent from the source to the sink.

Full duplex
Possibility of simultaneous sending and receiving.

Half duplex
Alternating send and receive possibilty on one conduction (multiplexed).

Simplex
Only sending or receiving.

Push-pull operation
In push-pull-operation, one wire carries the signal which has to be transmitted, the second one the inverted signal (symmetrical conduction). On the end of the line, the difference of the two signal amplitudes is calculated. That way, common-mode interferences like crosstalk and noise have near to no effect on the transmission.